DRDO Placement Paper Aptitude - General -31 Dec 2010

Posted by FreshersWorld

7 Jan, 2012

Model for ECE: Direct Theory question: 1. A triangular-square wave generator uses * A sine wave oscillator and a comparator * An integrator and a comparator * A diffrentiator and comparator * A sine wave oscillator and a clipper 2. An amplifier has two identical cascaded stages. Each stage has a BW of 20KHz. The overall BW shall be * 10KHz * 12.9KHz * 20KHz * 28.3HHz

Direct numerical problem:

A parabolic dish antenna has a diameter of 1m. the maximum possible ideal gain of the antenna at a wavelength 3.14cm is * 20 dB * 30 dB * 40 dB * 50 dB

The frequency deviation produced in a VHF carrier by a signal of 100Hz is 50KHz. The frequency modulation is 100 radians 250 radians 500 radians 750 radians

Application based theoretical or numerical problem:

Which one of the pulses has the same form in time domain as well as in frequency domain Rectangular Exponenetial Triangular Gaussian

Good voice reproduction via PCM requires 128 quantisation levels. If the BW of voice channel is 4KHz then data rate is 256 Kbps 128 Kbps 56 Kbps 28 Kbps

Match the following: 1. List 1 List2 A. Thyristor 1. Second break down B. MOSFET 2. Large on-state drop C. IGBT 3. Small on state drop D. BJT 4. Slow device

A. Free and forced response 1. Discrete time systems B. Z transform 2. Dirichlet conditions C. Probability theory 3. Non-homogenous differential equation d. Fourier series 4. Random process

The following item consists of two statements labeled as Assertion A and the other as Reason R. Use the following codes: (a) Both A&R are individually true and R is the correct explanation of A (b) Both A & R are individually true and R is not the correct explanation of A (c) A is true and R is false (d) A is false and R is true

AEvery materials has a different value of energy band gap except metals which have no band gap R The energy band gap is decided by the equilibrium lattice constant, which is different in different materials.

AOp-amp are commonly used in instrumentation R Op-amps do not load the circuit due to their very high input impedance

Problem based on circuits and graphs:

Some examples: For circuits: HW rectifier, voltmeter, RC or RLC or RL transients, feedback systems, clipper, clamper, transistor biasing,555 circits, logic gates, counters, bridges and wattmeters. Graphs: Frequency response H(s),open loop gain from root loci, Nyquist plot, transfer functions etc

Ad Blocker Detected

We have noticed that you have an ad blocker enabled which restricts ads served on the site.
Please disable it to continue using Downloadmela.

Model for ECE:Direct Theory question:

1. A triangular-square wave generator uses

* A sine wave oscillator and a comparator

* An integrator and a comparator

* A diffrentiator and comparator

* A sine wave oscillator and a clipper

2. An amplifier has two identical cascaded stages. Each stage has a BW of 20KHz. The overall BW

shall be

* 10KHz

* 12.9KHz

* 20KHz

* 28.3HHz

Direct numerical problem:* 20 dB

* 30 dB

* 40 dB

* 50 dB

100 radians

250 radians

500 radians

750 radians

Application based theoretical or numerical problem:Rectangular

Exponenetial

Triangular

Gaussian

256 Kbps

128 Kbps

56 Kbps

28 Kbps

1. List 1 List2

A. Thyristor 1. Second break down

B. MOSFET 2. Large on-state drop

C. IGBT 3. Small on state drop

D. BJT 4. Slow device

Codes:

(a) A-4, B-3, C-2, D-1 (b) A-1, B-2, C-3, D-4

(c) A-4, B-2, C-3, D-1 (d) A-1, B-3, C-2, D-4

A. Free and forced response 1. Discrete time systems

B. Z transform 2. Dirichlet conditions

C. Probability theory 3. Non-homogenous differential equation

d. Fourier series 4. Random process

Codes:

(a) A-1, B-3, C-2, D-4 (b) A-3, B-1, C-2, D-4

(c) A-1, B-3, C-4, D-2 (d) A-3, B-1, C-4, D-2

Assertion and reasoning type:

The following item consists of two statements labeled as Assertion A and the other as Reason R. Use the following codes:

(a) Both A&R are individually true and R is the correct explanation of A

(b) Both A & R are individually true and R is not the correct explanation of A

(c) A is true and R is false

(d) A is false and R is true

R The energy band gap is decided by the equilibrium lattice constant, which is different in different materials.

R Op-amps do not load the circuit due to their very high input impedance

Problem based on circuits and graphs:Some examples:

For circuits: HW rectifier, voltmeter, RC or RLC or RL transients, feedback systems, clipper, clamper, transistor biasing,555 circits, logic gates, counters, bridges and wattmeters.

Graphs: Frequency response H(s),open loop gain from root loci, Nyquist plot, transfer functions etc