BEML  Placement Paper   Whole Testpaper   UBDT College Of Engg, Davangere-30 Mar 2010

BEML  Placement Paper   Whole Testpaper   UBDT College Of Engg, Davangere-30 Mar 2010


  • Posted by  FreshersWorld 
    7 Jan, 2012

     

     

     

     

     

     

     

    BEL OBJECTIVE QUESTIONS

    Hi Friends,  Myself   R SUBRAMANYA  from UBDT Clg of ENGG Davangere (MECHANICAL STREAM).

    BEL visited my Clg on 30th March 2010 for recruitment. Their Selection process consist of 2 stages-Written technical test followed by HR Interview.  And the Technical Qs out of 70, i remember are as follows.....

    1.       SI Unit of temperature....

    2.       Unit of Young?s modulus....

    3.       Property of fluid which offers resistance against Tensile stress...

    4.       Mercury do not wet the glass, this is because of.....

    5.       Which law states that Specific heat is constant at all temp and pressures...

    6.       Seam Welding is a.......

    7.       The welding process which uses a consumable Electrode......

    8.       Steel balls are produced by....

    9.       The gear box in an automobile is located between....

    10.   Supercharging is very much essential in......

    11.   Superheating is done at...

    12.   Priming is needed in.....

    13.   Which of the following pump is used for lifting viscous fluids...

    14.   Scavenging is the process of..

    15.   Dew point temperature

    16.   Wet bulb temperature...

    17.   Most of the domestic refrigerators works on........cycle

    18.   Which of the following joining process has lowest strength...

    19.   Copper is (About spot welding)...

    20.   The very essential desired property of an measuring instrument is....

    21.   Precision is defined as

    22.   CPM is the technique of...

    23.   Value Engg is the study of..

    24.   In a press work, the size of the hole pierced is dependent on the...

    25.   Trimming is associated with...

    26.   Rivets are made of........materials

    27.   The decrease /absence of toughness of a material implies that the material is..

    28.   The property of material by which it can be beaten into plates is called....

    29.    Type of chips produced while machining Cast iron are....

    30.   Bearings which require no lubrication are called....

    31.   Ceramics are produced by....

    32.   The accuracy of holes are measured with..

    33.   Tool life depends on....

    34.   Surface tension is...

    35.   Engine pistons are made by Aluminium because it is....

    36.   No lubricant is required while cutting threads on....

    37.   The internal and external taper in a Turret lathe are achieved by...

    38.   The scientific study of human and his relations in an organisation is called....

    39.   1 Tonne of refrigeration is referred to....hours

    40.   Blades of Gas turbine are made up of.....

    41.   Crater wear occurs on.....portion of tool

    42.   Gears used to transmit power from non parallel and non intersecting shafts.......

    43.   The general gas equation...

    44.   The change of entropy depends on....

    45.   With 100% relative humidity, the wet bulb temp...(With regard to dew point temp)

    46.   When two pieces are joined together by butt with a cover plate with two rows of rivets is called..

    47.   The process of increasing hardness by cold working is called....

    48.   Ratio of Indicated HP and Brake HP is known as....

    49.   The product of mass and velocity is called as...

    50.   One watt is equal to.....

    51.   The lathe is having...... a) Internal threads

    52.   The bed of lathe is made by....(Material)

    53.   Gantt charts are used for....

    54.   Basic tool for work study......

    55.   .............................

     

     

    Questions asked in HR Round are as follows..

    1.       Tell about yourself....

    2.       I had work experience of 14 months in ESSAR STEELS, I have explained my nature of job, type of material, machine.

    3.       Few Questions on my previous  job..

    4.       What is fit, types of fits, Ex..

    5.       Topic switched over to Favourite Sub?s.. I said Fluid mechanics, Material Science and Manufacturing Technology..

    6.       Truely saying, MATERIALS SAVED MEJ, Nearly 20 Questions were on Heat treatment, Failure criterions, and mechanical properties.. Guys, be very much particular with the properties, All what they ask is only about BASIC, BASICs and more BASIC Fundamentals....

    7.       Gear terminology, Poisson?s ratio, hardness, toughness....

    8.       One more imp thing, if is there are any constant values like E, K G etc, clearly tell..

    9.       At the end of session they asked where you would like to work n al.. I have confidently answered as to work in R&D, because I am interested in Research, would like to develop new materials, and its my dream to Contribute something to my COUNTRY....

     

    Finally We ended up with a SMILE, WISH YOU ALL THE BEST............

2009-2016 downloadmela.com. All rights reserved.